Brake Problems
Hello readers, welcome to all of you in another new post, in this post we will know what are brake problems, the braking system is used in an automobile and there are many types of problems in braking systems, which have to be fixed according to time. Similarly, in this post, we will know about some brake problems coming in the braking system, so let’s know about braking problems without delay what are the Brake Problems
.
Following are the problems commonly encountered in brakes
Burning Smells
This type of problem is usually seen in the braking system, in this type of problem, the smell of burning from the vehicle when the brake is applied in the vehicle, this type of problem is usually due to overheating of the disc plate of the vehicle or due to brake fluid. In addition, if the vehicle is moving downhill, the drawer uses the brakes more to control the speed, causing the disc and brake fluid to overheat.
solution – In case of this type of problem in the car, first of all, the vehicle should be stopped immediately, and then hand brake should be applied then the bonnet of the car should be opened and wait till the disc cools down and the brake fluid cools down and then travel Should start and then get brake check done from the nearest service center and the problem should be rectified
Read Also  slack adjusters | Working | Types
Brake Light On
You all know very well that a warning light lights up when braking is applied, but sometimes some problems come in it, the warning light lights up on the dashboard, if this type of problem is seen on the dashboard then immediately check the braking system
Car Pulling to One Side When Braking
In this type of problem, when the brake is applied in the vehicle, the vehicle pulls to one side. Has happened or the disc has become jammed such as disc jam due to dust, rust, etc.
solution The brake should be properly checked and the problem should be fixed
Leaking Fluid
This type of problem is often seen in vehicles because when brakes are applied in a vehicle, many parts of the braking system work together, which sometimes leads to problems like leaking in braking fluid or fluid tank. I run out of fluid so the brakes don’t work properly
Solution- First of all check the brake system properly like checking the fluid reservoir and checking the fluid level if the level is low then complete the level of fluid and also if there is any leakage in it then correct it
Noises Grinding
The braking system uses metal on the brake pads and when these brake pads start to wear out, due to the rubbing on the brake drum, a very loud noise comes from it which is a symptom of a bad brake, this type of problem is disc type and drum I have and almost all brakes can have this type of problem
Solution – The reason for this type of problem is that the brake pads are worn out, so by checking the pads, the problem should be removed if the pads are damaged then change the new pads sometimes due to any other problem also the noise comes from the brake pads
Steering and brake pad vibration problem
The main reason for this type of problem is the rotor. If there is any kind of problem in the rotor, then in that case this problem can arise whenever the brake is applied, the brake rotor pushes the disc, and the car stops. But if the brake rotor is faulty or worn out, the brake will not function properly as the rotor and disc are not connected properly due to which vibration is felt in the steering and brake pads of the vehicle.
solution – If you see this type of problem, go to the service center and get the brakes checked and the problem fixed
Read Also   What Is a Camshaft | Working
                        Mechanical brake problems
Let’s know about some problems related to mechanical brakes which are as follows
Braking less
This type of problem is commonly seen in vehicles, there can be some of the following reasons for this type of problem.
The brake shoe is not adjusted properly – Check and adjust the brake shoe properly
Brake shoes are worn out or shorted, replace brake shoes if this happens
The brake cable and leakage are not adjusted properly or the brake cable is loose or there is any leakage Also check the anchor plate and adjust it properly
Additionally, if there is a problem with the brake drum or disc, check it properly and fix the problem.
Brakes noice
This type of problem in a brake system can be caused by some of the following:
One of the reasons for this could be that there is a problem with the brake drum like the diameter of the brake drum is not correct.
The anchor plate is not adjusted properly or has become loose, in addition, the rabbit on the brake shoe lining has become loose, due to which the brakes make noise.
The brake shoe is not centered correctly or the guide spring on the brake shoe is not properly assembled, it also makes brake noise
Brakes stay on
Sometimes this type of problem is also seen in the brake system, due to which there can be some reasons, some of which are as follows.
First of all, check the brake shoe return spring properly. Usually, this happens when the brake shoe spring is weak or broken.
The problem with the rocker is seen, if this type of problem appears, the spring should be replaced.
Apart from this, also check the brake shoe spring pin as it gets jammed sometimes and also check the leakage of the brake shoe and also check the lubricant and remove the problem.
Brakes are applied only when the brake foot is fully pressed
Many times this type of problem is also seen in the brake system also, let us know some of the reasons.
One of the reasons for is this type of problem can be wear of the brake lining should be checked properly if needed brake lining should be adjusted properly and the problem should be fixed
Another reason for this can be that the brake cable has been cut from somewhere or else or there is any kind of leakage in it, in this case, the cable should be checked and replaced if necessary.
Sometimes this type of problem is seen even when there is a difference between the brake shoe and the brake drum, there is a difference between the brake and drum, due to which the proper attachment of the brake shoe and the brake drum is not possible.
Another reason for applying the brake only after fully applying the brake pedal may be that the shoe expandible cam is worn out or the brake pedal is not properly adjusted, due to which this type of problem occurs.
Spongy brake
This type of problem is also commonly seen, let us know what could be the reason for this type of problem.
One reason for this type of problem may be that there is some fault in the brake shaft used in the brake system or the adjustment is not correct, in this case, check the brake system properly and remove the problem.
One of the main reasons for this type of problem can also be that there is some defect in the brake cable or there is excessive tension, in which case the brake cable should be checked and replaced, as well as the cross shaft, should be checked and adjusted properly.
Now you know what are the problems in mechanical brakes, now we will know what are the problems in hydraulic brakes.
Read Also   WHAT IS A DUAL AIR BRAKE SYSTEM?
                             Hydraulic brake problems
Let us know what problems come with hydraulic brakes and how to overcome those problems, we are going to discuss them further, so let’s know about hydraulic brakes.
slow down
This type of problem is also commonly seen in the hydraulic brake system, sometimes the brakes are less on applying the brakes, the following can be the reason for this type of problem
Another reason for the brake being reduced in the vehicle is the wear and tear of the brake lining. This type of reason causes the problem of fewer brakes. The brake lining of the vehicle should be checked properly.
Brakes apply only when the brake pedal is fully applied
This type of problem is also commonly seen, often the brake is applied before pressing the brake pedal completely, but due to some fault in the brake, the brake is applied only when the brake pedal is fully pressed, which causes trouble. This type of problem Following are some of the reasons
The Master cylinder is used in the hydraulic brake system and brake oil is filled in this cylinder. This type of problem occurs when the level of brake oil is less than the measurement, the level of brake oil in the master cylinder should be correct, apart from this the master cylinder This type of problem occurs even when there is garbage in it, as well as the check valve of the master cylinder, should also be checked that the valve is working properly.
Also, there is any kind of leakage in the master cylinder or other components that are damaged.
One reason for this type of problem is that air has entered the braking system from somewhere, due to which the brakes are not able to work properly, in such a problem, air bleeding should be done from the braking system.
Check the brake pedal also properly, due to not adjusting the brake pedal properly, this type of problem also occurs and the brakes are not able to work properly.
Spongy brake
This type of problem is also similar to mechanical brakes, let us know what are the causes of spongy brake problems in hydraulic brake systems.
One reason for this type of problem in the hydraulic brake system can be the presence of air in the braking system because the brakes are not able to function properly due to air coming into the hydraulic brake system or there is any leakage in the brake system due to which this type of problem occurs. problem occurs
Apart from this, this type of problem also occurs due to damage to the brake hose pipe and this type of problem also occurs due to damage to the secondary cup and brake oil. In this case, checking the braking system should remove the deficiency.
Noise on brake application
There can be some reasons for this type of problem such as the brake shoe is not adjusted properly or the lining of the brake shoe being worn out, the rabbit has become loose, the anchor plate is not adjusted properly or there being some defect in the brake drum due to which On applying the brakes, there is a loud noise from the brakes, in this case, the brake system should be checked properly and the deficiency should be removed.
Read Also  Turbocharger | Working | Types
                     Air Brake Problems
Let us now know what kind of problems come with the air brake.
Brake failure
This type of problem is seen in the air brake system, sometimes the brakes do not work properly, there are some reasons which are as follows
This reason is common in the air brake systems and in almost all brake systems and that is the wear and tear of brake lining or due to reduction in friction of lining, this type of problem is also seen, for this check brake lining properly and in case of need
Replace brake liner
Another reason for this is the lack of air in the air brake system because air is used for braking in the air brake system and the air pressure in the brake system should be correct if the pressure is not created properly and the brakes work properly Apart from this, if there is some defect in the brake drum, then this type of problem is also seen.
Air tank pressure drop
This type of problem is also seen in air brake systems that Do or sometimes don’t work Air pressure in the air brake system should be kept adequate
Read Also  Gearbox couplings | types |working
Doesn’t disengage after braking
This type of problem is also seen many times, in this type of problem, whenever the pedal is pressed to apply a brake and after that when the pedal is released, the brakes do not disengage but remain engaged. There are some reasons for this type of problem, about which we will know, so let’s know some of the following reasons
First of all, see whether the adjustment of the brake shoe is correct or not, if the adjustment is not correct, then if the brake drum is not of the correct diameter, then this type of problem is also seen, in this situation, the brake drum should be replaced and Brake shoe adjustment must be done
There are many other reasons why there is a problem of not brake disengage like wheel bearings have become loose or brake lining not able to disconnect from the drum and brake valves are damaged or if the brake chamber push rod speed is more than this What type of problem is found in an air brake system?
The Air compressor makes loud noises
This type of problem is also commonly seen in the air brake system, in which there is a loud noise from the air pressure which is a symptom of a bad brake. Some of the reasons for this type of problem are as follows.
There can be many reasons for this type of problems like the loosening of a driving pulley, a large gap between two driver gears, and malfunctioning compressor bearings. To correct this problem, the air compressor should be checked and rectified.
Stop light switch
A stop light switch is used as an indicator in a motor vehicle. In a traffic signal, the vehicle is slowing down or brakes are being applied. This information is given through the stop light switch. This switch is connected to the master cylinder. it works as a unit it uses two terminals one terminal is positive and the wire connected to the other terminal is connected to the stop light switch whenever the brake pedal is pressed in the switch The diaphragm connected by hydraulic oil pressure completes the electrical circuit by connecting the two terminals, which causes the light to burn. The diaphragm spring retracts to separate the two terminals. Also, in motor vehicles with mechanical brakes, a special type with a brake pedal. A pull-and-push switch is used for this purpose by making a mechanical arrangement. When the brake pedal is applied, the switch is depressed by means of a mechanical link, completing the electrical circuit and lighting the stop light switch, and when the brake pedal is applied, the switch is depressed. If the pressure is released from the switch breaks the circuit and the light goes off
Sometimes due to some problem with the stop light switch, it does not work properly, due to which the indication does not work properly, the stop light switch should be checked regularly and in case of a problem, it should be replaced or repaired immediately. should



Disc brake problem
Let us know about some problems related to disc brakes which are commonly seen in vehicles, some problems are similar to disc brakes but some are different because the disc pad is used to stop the wheel in a disc brake. Disc brakes also have problems compared to other brakes, about which we are going to know, so without delay, let us know about some problems which are commonly seen.
Brake jam
This type of problem is also commonly seen when the brake of the vehicle gets jammed. There may be some reasons for this type of problem like the disc plate getting crooked or the return spring not working properly or jammed. It is known that the piston used in the disc brake does not work properly, due to which the brakes get jammed. On seeing this type of problem, the brake system should be checked properly and the deficiency should be removed.
Brake failure
This type of problem is also commonly seen in the braking system, in which the brakes do not work properly after applying the brakes in the vehicle, either the brakes are less or do not apply, usually there are some reasons for this type of problem. can
Apart from this, due to the wear of the disc pads, there is also a problem in the braking system, in which case the brake pads should be replaced.
Due to the lack of brake oil in the master cylinder, it is also commonly seen. When this type of problem occurs, the level of brake oil in the master cylinder should be checked and the level should be kept favorable.
Apart from this, the hydraulic pressure does not work properly due to the arrival of air in the braking system, which does not apply the brakes properly, in this case, air bleeding should be done from the braking system and the level of brake oil in the master cylinder should be kept correct.
What have you learned?
In this post, you have learned about the problems related to brakes and their solutions, it is expected that you have got to know about this post. How did you like this post, send your suggestions to us in the comment box and if you have any questions in your mind, then ask us in the comment box. Will try to answer your questions as well as share this post with others and follow us on social media
Thank you